5kp5.0 thru 5kp188a vishay general semiconductor document number: 88308 revision: 21-oct-08 for technical questions within your r egion, please contact one of the following: pdd-americas@vishay.com , pdd-asia@vishay.com , pdd-europe@vishay.com www.vishay.com 1 t rans z orb ? transient voltage suppressors features ? p600, glass passivated chip junction ? available in uni-directional polarity only ? 5000 w peak pulse power capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % ? excellent clamping capability ? very fast response time ? low incremental surge resistance ? solder dip 260 c, 40 s ? component in accordance to rohs 2002/95/ec and weee 2002/96/ec typical applications use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ics, mosfet, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. mechanical data case: molded epoxy body over passivated junction molding compound meets ul 94 v-0 flammability rating base p/n-e3 - rohs comp liant, commercial grade base p/nhe3 - rohs co mpliant, high reliability/ automotive grade (aec q101 qualified) terminals: matte tin plated leads, solderable per j-std-002 and jesd22-b102 e3 suffix meets jesd 201 class 1a whisker test, he3 suffix meets jesd 201 class 2 whisker test polarity: color band denotes cathode end primary characteristics v wm 5.0 v to 188 v p ppm 5000 w p d 8.0 w i fsm 500 a t j max. 175 c case style p600 notes: (1) non-repetitive current pulse, per fig. 3 and derated above t a = 25 c per fig. 2 (2) measured on 8.3 ms single half si ne-wave or equivalent square wave, dut y cycle = 4 pulses per minute maximum maximum ratings (t a = 25 c unless otherwise noted) parameter symbol value unit peak pulse power dissipatio n with a 10/1000 s waveform (1) p ppm 5000 w peak pulse current with a 10/1000 s waveform (1) i ppm see next table a power dissipation on infi nite heatsink at t l = 75 c (fig. 5) p d 8.0 w peak forward surge current 8.3 ms single half sine-wave (fig. 5) i fsm 600 a instantaneous forward voltage at 100 a (2) v f 3.5 v operating junction and storage temperature range t j , t stg - 55 to + 175 c
5kp5.0 thru 5kp188a vishay general semiconductor www.vishay.com for technical questions within your region, please contact one of the following: pdd-americas@vishay.com , pdd-asia@vishay.com , pdd-europe@vishay.com document number: 88308 revision: 21-oct-08 2 electrical characteristics (t a = 25 c unless otherwise noted) device type breakdown voltage v br (v) (1) test current at i t (ma) stand-off voltage v wm (v) maximum reverse leakage at v wm i d (a) maximum peak pulse current i ppm (2) (a) maximum clamping voltage at i ppm v c (v) maximum temperature coefficient of v br (%/c) min. max. 5kp5.0 6.40 7.30 50 5.0 2000 521 9.6 0.057 5kp5.0a 6.40 7.00 50 5.0 2000 543 9.2 0.057 5kp6.0 6.67 8.15 50 6.0 5000 439 11.4 0.061 5kp6.0a 6.67 7.37 50 6.0 5000 485 10.3 0.061 5kp6.5 7.22 8.82 50 6.5 2000 407 12.3 0.065 5kp6.5a 7.22 7.98 50 6.5 2000 446 11.2 0.065 5kp7.0 7.78 9.51 50 7.0 1000 376 13.3 0.068 5kp7.0a 7.78 8.60 50 7.0 1000 417 12.0 0.068 5kp7.5 8.33 10.2 5.0 7.5 250 350 14.3 0.073 5kp7.5a 8.33 9.21 5.0 7.5 250 388 12.9 0.073 5kp8.0 8.89 10.9 5.0 8.0 150 333 15.0 0.075 5kp8.0a 8.89 9.83 5.0 8.0 150 368 13.6 0.075 5kp8.5 9.44 11.5 5.0 8.5 50 314 15.9 0.078 5kp8.5a 9.44 10.4 5.0 8.5 50 347 14.4 0.078 5kp9.0 10.0 12.2 5.0 9.0 20 296 16.9 0.081 5kp9.0a 10.0 11.1 5.0 9.0 20 325 15.4 0.081 5kp10 11.1 13.6 5.0 10.0 15 266 18.8 0.084 5kp10a 11.1 12.3 5.0 10.0 15 294 17.0 0.084 5kp11 12.2 14.9 5.0 11.0 10 249 20.1 0.086 5kp11a 12.2 13.5 5.0 11.0 10 275 18.2 0.086 5kp12 13.3 16.3 5.0 12.0 5.0 227 22.0 0.088 5kp12a 13.3 14.7 5.0 12.0 5.0 251 19.9 0.088 5kp13 14.4 17.6 5.0 13.0 2.0 210 23.8 0.090 5kp13a 14.4 15.9 5.0 13.0 2.0 233 21.5 0.090 5kp14 15.6 19.1 5.0 14.0 2.0 194 25.8 0.092 5kp14a 15.6 17.2 5.0 14.0 2.0 216 23.2 0.092 5kp15 16.7 20.4 5.0 15.0 2.0 186 26.9 0.094 5kp15a 16.7 18.5 5.0 15.0 2.0 205 24.4 0.094 5kp16 17.8 21.8 5.0 16.0 2.0 174 28.8 0.096 5kp16a 17.8 19.7 5.0 16.0 2.0 192 26.0 0.096 5kp17 18.9 23.1 5.0 17.0 2.0 164 30.5 0.097 5kp17a 18.9 20.9 5.0 17.0 2.0 181 27.6 0.097 5kp18 20.0 24.4 5.0 18.0 2.0 155 32.2 0.098 5kp18a 20.0 22.1 5.0 18.0 2.0 171 29.2 0.098 5kp20 22.2 27.1 5.0 20.0 2.0 140 35.8 0.099 5kp20a 22.2 24.5 5.0 20.0 2.0 154 32.4 0.099 5kp22 24.4 29.8 5.0 22.0 2.0 127 39.4 0.100 5kp22a 24.4 26.9 5.0 22.0 2.0 141 35.5 0.100 5kp24 26.7 32.6 5.0 24.0 2.0 116 43.0 0.101 5kp24a 26.7 29.5 5.0 24.0 2.0 129 38.9 0.101 5kp26 28.9 35.3 5.0 26.0 2.0 107 46.6 0.101 5kp26a 28.9 31.9 5.0 26.0 2.0 119 42.1 0.101 5kp26a 28.9 31.9 5.0 26.0 2.0 119 42.1 0.101 5kp28 31.1 38.0 5.0 28.0 2.0 100 50.1 0.102 5kp28a 31.1 34.4 5.0 28.0 2.0 110 45.4 0.102 5kp30 33.3 40.7 5.0 30.0 2.0 93.5 53.5 0.103 5kp30a 33.3 36.8 5.0 30.0 2.0 103 48.4 0.103 5kp33 36.7 44.9 5.0 33.0 2.0 84.7 59.0 0.104 5kp33a 36.7 40.6 5.0 33.0 2.0 93.8 53.3 0.104 5kp36 40.0 48.9 5.0 36.0 2.0 77.8 64.3 0.104 5kp36a 40.0 44.2 5.0 36.0 2.0 86.1 58.1 0.104
5kp5.0 thru 5kp188a vishay general semiconductor document number: 88308 revision: 21-oct-08 for technical questions within your r egion, please contact one of the following: pdd-americas@vishay.com , pdd-asia@vishay.com , pdd-europe@vishay.com www.vishay.com 3 notes: (1) pulse test: t p 50 ms (2) surge current waveform per fig. 3 and derate per fig. 2 (3) all items and symbols are consistent with ansi/ieee c62.35 5kp40 44.4 54.3 5.0 40.0 2.0 70.0 71.4 0.105 5kp40a 44.4 49.1 5.0 40.0 2.0 77.5 64.5 0.105 5kp43 47.8 58.4 5.0 43.0 2.0 65.2 76.7 0.105 5kp43a 47.8 52.8 5.0 43.0 2.0 72.0 69.4 0.105 5kp45 50.0 61.1 5.0 45.0 2.0 62.3 80.3 0.106 5kp45a 50.0 55.3 5.0 45.0 2.0 68.8 72.7 0.106 5kp48 53.3 65.2 5.0 48.0 2.0 58.5 85.5 0.106 5kp48a 53.3 58.9 5.0 48.0 2.0 64.6 77.4 0.106 5kp51 56.1 69.3 5.0 51.0 2.0 54.9 91.1 0.107 5kp51a 56.7 62.7 5.0 51.0 2.0 60.7 82.4 0.107 5kp54 60.0 73.3 5.0 54.0 2.0 51.9 96.3 0.107 5kp54a 60.0 66.3 5.0 54.0 2.0 57.4 87.1 0.107 5kp58 64.4 78.7 5.0 58.0 2.0 48.5 103 0.107 5kp58a 64.4 71.2 5.0 58.0 2.0 53.4 94 0.107 5kp60 66.7 81.5 5.0 60.0 2.0 46.7 107 0.108 5kp60a 66.7 73.7 5.0 60.0 2.0 51.7 97 0.108 5kp64 71.1 96.9 5.0 64.0 2.0 43.9 114 0.108 5kp64a 71.1 78.6 5.0 64.0 2.0 48.5 103 0.108 5kp70 77.6 95.1 5.0 70.0 2.0 40.0 125 0.108 5kp70a 77.8 86.0 5.0 70.0 2.0 44.2 113 0.108 5kp75 83.3 102 5.0 75.0 2.0 37.3 134 0.108 5kp75a 83.3 92.1 5.0 75.0 2.0 41.3 121 0.108 5kp78 86.7 106.0 5.0 78.0 2.0 36.0 139 0.108 5kp78a 86.7 95.8 5.0 78.0 2.0 39.7 126 0.108 5kp85 94.4 115 5.0 85.0 2.0 33.1 151 0.108 5kp85a 94.4 104 5.0 85.0 2.0 36.5 137 0.110 5kp90 100 122 5.0 90.0 2.0 31.3 160 0.110 5kp90a 100 111 5.0 90.0 2.0 34.2 146 0.110 5kp100 111 136 5.0 100 2.0 27.9 179 0.110 5kp100a 111 123 5.0 100 2.0 30.9 162 0.110 5kp110 122 149 5.0 110 2.0 25.5 196 0.112 5kp110a 122 135 5.0 110 2.0 28.2 177 0.112 5kp120 133 163 5.0 120 2.0 23.4 214 0.112 5kp120a 133 147 5.0 120 2.0 25.9 193 0.112 5kp130 144 176 5.0 130 2.0 21.6 230 0.112 5kp130a 144 159 5.0 130 2.0 23.9 209 0.112 5kp150 167 204 5.0 150 2.0 18.7 268 0.112 5kp150a 167 185 5.0 150 2.0 20.6 243 0.112 5kp160 178 218 5.0 160 2.0 17.4 287 0.112 5kp160a 178 197 5.0 160 2.0 19.3 259 0.112 5kp170 189 231 5.0 170 2.0 16.4 304 0.112 5kp170a 189 209 5.0 170 2.0 18.2 275 0.112 5kp188 209 255 5.0 188 2.0 14.5 344 0.112 5kp188a 209 231 5.0 188 2.0 15.2 328 0.112 electrical characteristics (t a = 25 c unless otherwise noted) device type breakdown voltage v br (v) (1) test current at i t (ma) stand-off vol tag e v wm (v) maximum reverse leakage at v wm i d (a) maximum peak pulse current i ppm (2) (a) maximum clamping voltage at i ppm v c (v) maximum temperature coefficient of v br (%/c) min. max.
5kp5.0 thru 5kp188a vishay general semiconductor www.vishay.com for technical questions within your region, please contact one of the following: pdd-americas@vishay.com , pdd-asia@vishay.com , pdd-europe@vishay.com document number: 88308 revision: 21-oct-08 4 note: (1) automotive grade aec q101 qualified ratings and characteristics curves (t a = 25 c unless otherwise noted) ordering information (example) preferred p/n unit weight (g) preferred package code base quantity delivery mode 5kp5.0a-e3/54 2.776 54 800 13" diameter paper tape and reel 5kp5.0ahe3/54 (1) 2.776 54 800 13" diameter paper tape and reel figure 1. peak pulse power rating curve figure 2. pulse power or current vs. initial junction temperature 0.1 s 1.0 s 10 s 100 s 1 ms 10 ms 0.1 1.0 10 100 n on-repetiti v e p u lse w a v eform sho w n in fig. 3 t a = 25 c p ppm - peak p u lse po w er (k w ) t d - p u lse w idth 100 75 50 25 0 0 25 50 75 100 125 150 175 200 peak p u lse p o w er (p pp ) or c u rrent (i pp ) derating in percentage, % t j - initial temperat u re (c) figure 3. pulse waveform figure 4. typical junction capacitance 0 50 100 150 t r = 10 s peak v al u e i ppm half v al u e - i ppm i pp 2 t d 10/1000 s w a v eform as defined b y r.e.a. 0 1.0 2.0 3.0 4.0 t - time (ms) i ppm - peak p u lse c u rrent, % i rsm t j = 25 c p u lse w idth (t d ) is defined as the point w here the peak c u rrent decays to 50 % of i ppm 1 10 100 200 100 1000 10 000 100 000 c j - j u nction capacitance (pf) v w m - re v erse stand-off v oltage ( v ) meas u red at zero bias meas u red at stand-off v oltage v w m t j = 25 c f = 1.0 mhz v sig = 50 m v p-p
5kp5.0 thru 5kp188a vishay general semiconductor www.vishay.com for technical questions within your region, please contact one of the following: pdd-americas@vishay.com , pdd-asia@vishay.com , pdd-europe@vishay.com document number: 88308 revision: 21-oct-08 5 package outline dimensions in inches (millimeters) application note the 5kp series of high power transient voltage suppressors were designed to be used on the output of switching power supplies. these devices may be used to replace crowbar circuits. both the 5 % and 10 % voltage tolerances are referenced to the power supply output voltage level. they are able to withstand high levels of peak current while allowing a circuit breaker to trip or a fuse blow before shorting. th is will enable the user to reset the breaker or replace the fuse and continue operation. for this type operation, it is recommended that a sufficient mounting surface be used for dissipating the heat generated by the transient voltage suppressor during the transient or over-voltage condition. figure 5. power derating curve l = 0.375" (9.5 mm) lead lengths p d - po w er dissipation ( w ) t l - lead temperat u re (c) 60 hz resisti v e or ind u cti v e load 8 6 4 2 0 0 25 50 75 100 125 150 175 200 figure 6. maximum non-repetit ive forward surge current 1 10 100 200 300 400 500 450 350 250 8 .3 ms single half sine- w a v e nu m b er of cycles at 60 hz i fsm - peak for w ard s u rge c u rrent (a) 0.360 (9.1) 0.340 ( 8 .6) 0.052 (1.32) 0.04 8 (1.22) dia. 1.0 (25.4) mi n . 0.360 (9.1) 0.340 ( 8 .6) 1.0 (25.4) mi n . case style p600
document number: 91000 www.vishay.com revision: 18-jul-08 1 disclaimer legal disclaimer notice vishay all product specifications and data are subject to change without notice. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ?vishay?), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. vishay disclaims any and all li ability arising out of the use or application of any product describ ed herein or of any information provided herein to the maximum extent permit ted by law. the product specifications do not expand or otherwise modify vishay?s terms and conditions of purcha se, including but not limited to the warranty expressed therein, which apply to these products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay. the products shown herein are not designed for use in medi cal, life-saving, or life-sustaining applications unless otherwise expressly indicated. customers using or selling vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify vishay for any damages arising or resulting from such use or sale. please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such applications. product names and markings noted herein may be trademarks of their respective owners.
|
